 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Drawing No. JGC42-4256A P. 1/12 Specification of Piezoelectric Ceramic Resonator CSTCR4M00G53-R0 CSTCR4M00G53-B0 Date Approved by Checked by May 22, 2006 Issued by 1. Scope ((R)) This product specification is applied to the piezoelectric ceramic resonator used for time base oscillator in a microcomputer. Please contact us when using this product for any other applications than described in the above. 2. Part Number Murata Part Number Taping Bulk CSTCR4M00G53-R0 CSTCR4M00G53-B0 Customer's Part Number Customer's Drawing Number 3. Appearance and Dimensions 3-1 Appearance 3-2 (R) Dimensions of component 3-3 Construction : : No illegible marking. No visible dirt. : 1 : See Figure 1. Dimensions of taping type and bulk type are the same. : : Resonator and capacitor elements are mounted onto ceramic substrate, then metal cap covers over the elements. Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A P. 2/12 4. Electrical Characteristics 4-1 4-2 4-3 4-4 4-5 4-6 4-7 Item Specification Nominal Oscillating Frequency *1 Initial Tolerance *1 Resonant Impedance (C1,C2) Built-in Load Capacitance (C1,C2) Insulation Resistance Withstanding Voltage Rated Working Voltage (1)D.C. Voltage (2)A.C. Voltage Frequency Shift by Temperature (-20+80) (-20C to +80C) Operating Temperature Range Storage Temperature Range *2 Oscillating Frequency Aging *2 4.000MHz 0.50% 0.50% max. 60 60max 15pF20% () 15pF20%max. (ref.) 500M (D.C.10V ) 500Mmin. (Applied D.C.10V) D.C.100V, 5 D.C.100V, 5 seconds max. D.C.6V 15Vp-p. 4-8 4-9 0.2% () 0.2%max. (from initial value) -20+80 -20C to +80C -55+85 -55C to +85C 0.1% () 0.1%max. (from initial value) *1 (R)0.60% Terminal (1) and (3) are interchangeable, but if interchange initial tolerance is 0.60%max. *2 +85210001 Components shall be left in a chamber of +852C for 1000 hours, then measured after leaving in natural condition for 1 hour. Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A P. 3/12 5. Physical Characteristics Item 5-1 Specification After Test 1.0m3 1 4-3 Components shall be measured after 3 times No visible damage and random dropping on the wooden plate from the the measured values height of 1.0m. shall meet Table 1 and 4-3. 1055Hz1.5mm 14-3 X,Y,Z32 Applying the vibration of amplitude 1.5mm and The measured values vibration frequency 10 to 55Hz in each of 3 shall meet Table 1 and perpendicular directions for 2 hours. 4-3. 115 14-3 After components soldered on PCB, the load The measured values shall be applied to the PCB as shown in below shall meet Table 1 and figure for 5 times (1 second per 1 time). 4-3. Test Condition Random Drop 5-2 Vibration Resistance 5-3 Bend Strength PCB Stick 20 10 Load PCB R10 5 5 Supporter Deflection 1 1 Off-Center Part 45 45 / PCB thickness : 1.6mm / unit : mm Murata Manufacturing Co.,Ltd. 1 Drawing No. JGC42-4256A P. 4/12 5-4 Resistance to Soldering Heat (1) 2 14-3 1 (1) Re-flow Components shall be measured after applying The measured values Soldering twice of the re-flow soldering with following shall meet Table 1 and temperature profile and leaving in natural 4-3. condition for 1 hour. Temperature (C) Peak (260C / max.) 230 180 150 Heating (230C) Gradual Cooling Pre-heating (150-180C) 30 60 - 120 / sec. sec. min. 40 120 sec. max. sec. min. (2) +35053.00.524 1 4-3 (2)Soldering Components shall be measured after soldering No visible damage and with iron at +3505C for 3.00.5 seconds and leaving in the measured values natural condition for 24 hours. The soldering shall meet Table 1 and iron shall not touch the components while 4-3. soldering. 5-5 LF (Sn-3Ag-0.5Cu 90% PCT+105C100%R.H. 4 5 +2455C30.5 Solderability LF Solder (Sn-3Ag-0.5Cu The solder shall coat at After being kept in pressure cooker at +105C least 90% of the temperature and 100%R.H. for 4 hours, surface of terminal. terminals of components shall be immersed in a soldering bath at temperature of +2455C for 30.5 seconds after being placed in a rosinmethanol for 5 seconds. Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A P. 5/12 6. Environmental Characteristics Item 6-1 Dry Heat (Storage) Specification After Test +8521000 4-34-9 1 Components shall be left in a chamber The measured values (Temperature: +852C) for 1000 hours, then shall meet 4-3 and 4-9. measured after leaving in natural condition for 1 hour. -5521000 14-3 1 Components shall be left in a chamber The measured values (Temperature: -552C) for 1000 hours, then shall meet Table 1 and measured after leaving in natural condition for 1 4-3. hour. Test Condition +60290 +5 %R.H. 14-3 -0 6-2 Cold (Storage) 6-3 Humidity 6-4 Thermal Shock 10001 Components shall be left in a chamber (90 to The measured values 95%R.H. at +602C) 1000 hours, then shall meet Table 1 and measured after leaving in natural condition for 1 4-3. hour. -55C30 14-3 +85C30 110 1 After performing 10 cycles of thermal test (- The measured values 55C 30 minutes to +85C 30 minutes), shall meet Table 1 and components shall be left in natural condition for 4-3. 1 hour. 1 Table 1. Specification After Test 0.2% 0.2%max. (from initial value) Item Oscillating Frequency Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A P. 6/12 7. Test Circuit 7-1 Oscillating Frequency 7-2 : 2 : See Figure 2. : Equivalent Circuit Constants : Vector Impedance Analyzer HP4194A or Equivalent. : +2536010%R.H. +5+3545 85%R.H. : Standard conditions for the measurement shall be +253C temperature and 6010%R.H. humidity. The measurement shall be performed at the temperature of +5 to 35C and the humidity of 45 to 85%R.H. unless otherwise the result is doubtful. 7-3 Measuring Condition 8. Packaging Standard (Bulk) 500 Each minimum package unit of products (500 pcs) shall be in a carton box and it shall be clearly marked with part number, quantity and outgoing inspection number. 9. Packaging Standard (Taping) 9-1 () The tape for components shall be wound clockwise. The feeding holes shall be to the right side as the tape is pulled toward the user. 9-2 1 3,000 A reel shall contain 3,000pcs of components. 9-3 3 Dimensions of plastic tape are shown in Figure 3. 9-4 4 Dimensions of plastic reel are shown in Figure 4. Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A P. 7/12 10. ! Cautions 10-1 Limitation of Applications () Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. Aircraft equipment Aerospace equipment Undersea equipment Power plant control equipment Medical equipment Transportation equipment(vehicles, trains, ships, etc.) Traffic signal equipment Disaster prevention / crime prevention equipment Data-processing equipment Applications of similar complexity and/or with reliability requirements to the applications listed in the above 10-2 Fail-safe Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure of our product. Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A P. 8/12 11. Caution for Use 11-1 The component may be damaged if excess mechanical stress is applied. 11-2 Please do not apply excess mechanical stress to the component and terminals at soldering. 11-3 Conformal coating or washing to the component is not acceptable. Because it is not hermetically sealed. 11-4 Irregular or stop oscillation may occur under unmatched circuit conditions. 11-5 The component is recommended with placement machines with employ optical placement capabilities. The component might be resulted in damage by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines which utilize mechanical positioning. Please contact Murata for details beforehand. Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A P. 9/12 12. Notice on product storage 12-1 -10+401585% Please store the products in room where the temperature / humidity is stable. And avoid such places where there are large temperature changes. Please store the products under the following conditions : Temperature : -10 to +40 (degree C) Humidity : 15 to 85% R.H. 12-2 66 6 Expire date (Shelf life) of the products is 6 months after delivery under the conditions of a sealed and an unopened package. Please use the products within 6 months after delivery. If you store the products for a long time ( more than 6months ), use carefully because the products may be degraded in the solder-ability and/or rusty. Please confirm solder-ability and characteristics for the products regularly. 12-3 Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality, and/or be degraded in the solder-ability due to the storage in a chemical atmosphere. 12-4 Please do not put the products directly on the floor without anything under them to avoid damp places and/or dusty places. 12-5 Please do not store the products in the places such as : in a damp heated place, in a place where direct sunlight comes in, in place applying vibrations. 12-6 Please use the products immediately after the package is opened, because the characteristics may be reduced in quality, and/or be degraded in the solder-ability due to storage under the poor condition. 12-7 Please do not drop the products to avoid cracking of ceramic element. Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A P. 10/12 13. ! Note: 13-1 Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 13-2 You are requested not to use our product deviating from this product specification. 13-3 1 Please return one duplicate of this product specification to us with your signature to acknowledge your receipt. In case of no return within three months from submission date, or if we receive order before the duplicate is returned, this product specification will be deemed to have been received by you. 13-4 We consider it not appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents. Therefore, if your technical documents as above include such terms and conditions such as warranty clause, product liability clause, or intellectual property infringement liability clause, they will be deemed to be invalid. Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A 1 Figure 1. W P. 11/12 Dimensions 400 (3) 0.20.2 (2) * (1) 0.4(ref.) 0.40.05 1.4max. 0.30.2 W L T : 4.50.1 : 2.00.1 : 1.150.05 L : : 4.1max. T EIAJ Monthly Code mm in mm ( 0.4(ref.) 0.4(ref.) (Recommendable Land Pattern 0.8 0.7 0.8 0.7 0.8 0.80.1 0.80.1 0.80.1 0.40.1 0.40.1 0.40.1 0.4 0.4 1.5 Land Pattem 2.6 1.6 0.4 0.750.1 1.50.1 1.50.1 1.5 2 Figure 2. Test Circuit CERALOCK(R): CSTCR4M00G53-R0 CSTCR4M00G53-B0 VDD Output 5pF Rf 1M (To Frequency Counter) IC:1/6 TC4069UBP x2 (Toshiba) VDD:+50.1V Rf:1M CERALOCK R (1) (3) C1 C2 (2) Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A 3 Figure 3. 4.00.1 2.00.05 P. 12/12 Dimensions of Plastic Tape (CSTCR4M00G53-R0) +0.1 1.750.1 5.50.05 1.5 -0 (9.5) (3) 4.00.1 0.10.7N 1.5 +0.1 -0.0 2.20.1 0.1 to 0.7N The cover film peel strength force 300mm / The cover film peel speed 300mm/min. 4.70.1 (2) 3 Max. Cover Film 10 1.250.05 0.30.05 (1.85max) Direction of Feed 4 Figure 4. Dimensions of Plastic Reel (CSTCR4M00G53-R0) Trailer 160190 160 to 190 Leader Cover Film Components Empty 160 /min. 400560mm 400 to 560mm Empty 0 180 -1.5 13.00.2 2.00.5 13.0 +1.0 0 17.01.0 mm in mm Murata Manufacturing Co.,Ltd. 12.00.2 mm in mm (1) |
Price & Availability of CSTCR4M00G53-B0
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |